Milan Cafe

Width 3" | Height 30" | Depth 3/4"

Base filler that comes as a flat panel and will not have a toe-kick recessed area on the bottom. It will be finished on two sides and edge-banded on all four edges.

Width 3" | Height 30" | Depth 3"

Corner filler that can be used instead of a blind corner cabinet. It will fill a gap between two cabinets in a corner, allowing the doors and drawers to still function properly, this will leave a void under the countertop.

Width 3" | Height 36" | Depth 3"

Corner filler that can be used instead of a blind corner cabinet. It will fill a gap between two cabinets in a corner, allowing the doors and drawers to still function properly, this will leave a void under the countertop.

Width 3" | Height 42" | Depth 3"

Corner filler that can be used instead of a blind corner cabinet. It will fill a gap between two cabinets in a corner, allowing the doors and drawers to still function properly, this will leave a void under the countertop.

Width 3" | Height 30" | Depth 13-7/8"

Wall column that can be trimmed on site if needed. The sides will be flush and finished, and the back will be unfinished.

Width 3" | Height 36" | Depth 13-7/8"

Wall column that can be trimmed on site if needed. The sides will be flush and finished, and the back will be unfinished.

Width 3" | Height 42" | Depth 13-7/8"

Wall column that can be trimmed on site if needed. The sides will be flush and finished, and the back will be unfinished.

Width 3" | Height 84" | Depth 24-7/8"

Tall column that can be trimmed on site if needed. The sides will be flush and finished, and the back will be unfinished.

Width 3" | Height 90" | Depth 24-7/8"

Tall column that can be trimmed on site if needed. The sides will be flush and finished, and the back will be unfinished.

Width 3" | Height 96" | Depth 24-7/8"

Tall column that can be trimmed on site if needed. The sides will be flush and finished, and the back will be unfinished.

Width 3" | Height 34-1/2" | Depth 24-7/8"

Base column that can be trimmed on site if needed. The sides will be flush and finished, and the back will be unfinished.

Width 3" | Height 34-1/2" | Depth 24-7/8"

Appliance end panel with a 3" return which consists of a filler interlocked with a 1/2" plywood return panel. The exposed sides will have near-flush finished ends. The front can be trimmed down to 1" wide if necessary (edge banding may be needed in order to finish the cut edge). The sides will be flush and finished and all four edges are edge-banded.

Width 3" | Height 96" | Depth 3/4"

Tall filler that will be finished on two sides and edge-banded on all four edges.

Width 3" | Height 30" | Depth 13-7/8"

Wall end panel with a filler attached to the front that will be finished on two sides and edge-banded on all four edges. The filler on the front will be flush with the side and can be cut down if needed. If it is cut, to avoid damage to the frame and side panels, please apply extra care when cutting the front panel, blue masking tape is the most commonly used to avoid splintering (strong adhesives must be avoided to avoid pulling the finish off).

Width 3" | Height 36" | Depth 13-7/8"

Wall end panel with a filler attached to the front that will be finished on two sides and edge-banded on all four edges. The filler on the front will be flush with the side and can be cut down if needed. If it is cut, to avoid damage to the frame and side panels, please apply extra care when cutting the front panel, blue masking tape is the most commonly used to avoid splintering (strong adhesives must be avoided to avoid pulling the finish off).

Width 3" | Height 42" | Depth 13-7/8"

Wall end panel with a filler attached to the front that will be finished on two sides and edge-banded on all four edges. The filler on the front will be flush with the side and can be cut down if needed. If it is cut, to avoid damage to the frame and side panels, please apply extra care when cutting the front panel, blue masking tape is the most commonly used to avoid splintering (strong adhesives must be avoided to avoid pulling the finish off).

Width 3" | Height 30" | Depth 3/4"

Wall filler that will be finished on two sides and edge-banded on all four edges.

Width 3" | Height 36" | Depth 3/4"

Wall filler that will be finished on two sides and edge-banded on all four edges.

Width 3" | Height 42" | Depth 3/4"

Wall filler that will be finished on two sides and edge-banded on all four edges.